76. MOD-6 and MOD-12 counters and multiples are most commonly used as:
(a) frequency counters
(b) multiplexed displays
(c) digital clocks
(d) power consumption meters
77. Select the response that best describes the use of the Master Reset on typical 4-bit binary counters.
(a) When MR1 and MR2 are both HIGH, all Qs will be reset to zero.
(b) When MR1 and MR2 are both HIGH, all Qs will be reset to one.
(c) MR1 and MR2 are provided to synchronously reset all four flip-flops.
(d) To enable the count mode, MR1 and MR2 must be held LOW.
78. Integrated-circuit counter chips are used in numerous applications including:
(a) timing operations, counting operations, sequencing, and frequency multiplication
(b) timing operations, counting operations, sequencing, and frequency division
(c) timing operations, decoding operations, sequencing, and frequency multiplication
(d) data generation, counting operations, sequencing, and frequency multiplication
79. A seven-segment, common-anode LED display is designed for:
(a) all cathodes to be wired together
(b) one common LED
(c) a HIGH to turn off each segment
(d) disorientation of segment modules
80. A principle regarding most display decoders is that when the correct input is present, the related output will switch:
(a) HIGH
(b) to high impedance
(c) to an open
(d) LOW
Related Posts
Counters » Exercise - 3 101. The counter circuit and associated waveforms shown below are for a(n) ________ counter, and the correct output waveform for QB is shown by waveform ________. (a) synchronous, a (b) asynchronous, b (c) synchronous, c (d) asynchronous, d 102. The given circuit is a(n) ________. (a) three-bit synchronous binary counter (b) eight-bit asynchronous binary flip-flop (c) two-bit asynchronous binary counter (d) four-bit asynchronous binary counter 103. Asynchronous counters are often called ________ counters. (a) toggle (b) ripple (c) binary (d) flip-flop 104. The given circuit represents a(n) ________. (a) four-bit binary counter (b) asynchronous BCD decade counter (c) synchronous BCD decade counter (d) BCD-to-decimal decoder 105. A BCD counter has ________ states. (a) 8 (b) 9 (c) 10 (d) 11 106. A sequential circuit design is used to ________. (a) count up (b) count down (c) decode an end count (d) count in a random order 107. The circuit shown below is a ________. (a) parallel in/serial out register (b) serial in/parallel load register (c) multiplexer (d) demultiplexer 108. In order to use a shift register as a counter, ________. (a) the register's serial input is the counter input and the serial output is the counter…- 151. The following waveform pattern is for a(n) ________. (a) 2-input AND gate (b) 2-input OR gate (c) Exclusive-OR gate (d) None of the above 152. The following waveform pattern is for a(n) ________. (a) 2-input AND gate (b) 2-input OR gate (c) Exclusive-OR gate (d) None of the above 153. The symbol shown represents a(n) ________. (a) AND gate (b) OR gate (c) NAND gate (d) NOR gate 154. The symbol shown represents ________. (a) AND-OR logic (b) AOI logic (c) XOR gate (d) XNOR gate 155. The expression can be directly implemented using only ________. (a) an XOR gate (b) an XNOR gate (c) an AOI circuit (d) three 2-input NAND gates 156. Assume you have A, B, C, and D available but not their complements. The minimum number of 2-input NAND gates required to implement the equation is ________. (a) 3 (b) 4 (c) 5 (d) 6 157. A gate can drive a number of load gate inputs up to its specified ________. (a) supply voltage (b) noise margin (c) fan-in (d) fan-out 158. If both inputs of a 2-input NOR gate are connected, the gate will function as an ________. (a) OR gate (b) AND gate…
- 251. The inputs/outputs of an analog multiplexer/demultiplexer are: (a) bidirectional (b) unidirectional (c) even parity (d) binary-coded decimal 252. Most demultiplexers facilitate which type of conversion? (a) decimal-to-hexadecimal (b) single input, multiple outputs (c) ac to dc (d) odd parity to even parity 253. What is the function of an enable input on a multiplexer chip? (a) to apply Vcc (b) to connect ground (c) to active the entire chip (d) to active one half of the chip 254. What is the status of the inputs S0, S1, and S2 of the 74151 eight-line multiplexer in order for the output Y to be a copy of input I5? (a) S0 = 0, S1 = 1, S2 = 0 (b) S0 = 0, S1 = 0, S2 = 1 (c) S0 = 1, S1 = 1, S2 = 0 (d) S0 = 1, S1 = 0, S2 = 1 255. One multiplexer can take the place of: (a) several SSI logic gates (b) combinational logic circuits (c) several Ex-NOR gates (d) several SSI logic gates or combinational logic circuits 256. How many select lines would be required for an 8-line-to-1-line multiplexer? (a) 2 (b) 3 (c) 4 (d) 8 257. One…
- Home » Computer Science » Data Communications and Computer Networks » Modem
- Home » Electronics Engineering » Digital Electronics » Counters