DC Biasing BJTs » Exercise – 1
1. For the BJT to operate in the active (linear) region, the base-emitter junction must be ________-biased and the base-collector junction must be ________-biased.
(a) forward, forward
(b) forward, reverse
(c) reverse, reverse
(d) reverse, forward
2. For the BJT to operate in the saturation region, the base-emitter junction must be ________-biased and the base-collector junction must be ________-biased.
(a) forward, forward
(b) forward, reverse
(c) reverse, reverse
(d) reverse, forward
3. The cutoff region is defined by IB ________ 0 A.
(a) >
(b) <
(c)
(d)
4. Nota
5. Calculate VCE.
(a) –4.52 V
(b) 4.52 V
(c) –9 V
(d) 9 V
Related Posts
- BJT » Exercise - 2 51. For a properly biased pnp transistor, let IC = 10 mA and IE = 10.2 mA. What is the level of IB? (a) 0.2 A (b) 200 mA (c) 200 A (d) 20.2 mA 52. Transistors are ________-terminal devices. (a) 2 (b) 3 (c) 4 (d) 5 53. How many carriers participate in the injection process of a unipolar device? (a) 1 (b) 2 (c) 0 (d) 3 54. Which of the following is (are) the terminal(s) of a transistor? (a) Emitter (b) Base (c) Collector (d) All of the above 55. List the types of bipolar junction transistors. (a) ppn, npn (b) pnp, npn (c) npp, ppn (d) nnp, pnp 56. The outer layers of a transistor are ________ the sandwiched layer. (a) much smaller than (b) the same as (c) much larger than (d) None of the above 57. How many individual pnp silicon transistors can be housed in a 14-pin plastic dual-in-line package? (a) 4 (b) 7 (c) 10 (d) 14 58. A transistor can be checked using a(n) ________. (a) curve tracer (b) digital meter (c) ohmmeter (d) Any of the above 59. What does a reading of a large or…
- BJT » Exercise - 1 1. A BJT has …… PN junction. (a) 1 (b) 2 (c) 3 (d) 4 2. A BJT has : (a) One PN junction (b) Two PN junctions (c) Three PN junctions (d) Four PN junctions 3. The gate of FET is analogous to the …….. of BJT. (a) Emitter (b) Collector (c) Base (d) None of these 4. A BJT is ......... controlled and the FET is ......... controlled device. (a) Current, Current (b) Voltage, Voltage (c) Voltage, Current (d) Current, Voltage 5. BJT with hfe=200, Ib=10 mA and IC= 4 mA is operating in : (a) Active region (b) Cut-off region (c) Saturation region (d) None of these 6. Which of the following statements is/are correct ? I. The DC load line is steeper than AC load line. II. BJT is a voltage controlled device. (a) Statement I (b) Statement II (c) Both statements I & II (d) Either statement I or II 7. In which mode of BJT operation are both junction reverse biased : (a) active (b) saturation (c) cut-off (d) revers active 8. In which mode of BJT operation are both junction forward biased : (a) active (b) saturation (c) cut-off (d) revers active 9. In a bipolar junction transistor the base region is made very thin so that :…
- DC Biasing BJTs » Exercise - 2 51. ________ is less dependent on the transistor beta. (a) Fixed bias (b) Emitter bias (c) Voltage divider (d) Voltage feedback 52. A significant increase in leakage current due to increase in temperature creates ________between IB curves. (a) smaller spacing (b) larger spacing (c) the same space as at lower temperature (d) None of the above 53. In any amplifier employing a transistor, the collector current IC is sensitive to ________. (a) (b) VBE (c) ICO (d) All of the above 54. In a collector feedback bias circuit, the current through the collector resistor is ________ and the collector current is ________. (a) IC, IC (b) IB + IC, IC (c) IB, IC (d) None of the above 55. The ________the stability factor, the ________sensitive the network is to variations in that parameter. (a) higher, more (b) higher, less (c) lower, more (d) None of the above