5555555555
12. An antilog amplifier has a ________ in series with the input.
(a) BJT
(b) diode
(c) diode or BJT
(d) resistor
| Subject Name : Electronics Engineering |
| Exam Name : IIT GATE, UPSC ESE, RRB, SSC, DMRC, NMRC, BSNL, DRDO, ISRO, BARC, NIELIT |
| Posts Name : Assistant Engineer, Management Trainee, Junior Engineer, Technical Assistant |
| Electronics & Communication Engineering Books
|
| GATE 2023 Total Info | ENGG DIPLOMA | UGC NET Total Info |
| IES 2023 Total Info | PSUs 2022 Total Info | CSIR UGC NET Total Info |
| JAM 2023 Total Info | M TECH 2023 Total Info | RAILWAY 2022 Total Info |
Related Posts
555555555529. A log amplifier has ________ in the feedback loop. (a) a diode (b) a BJT (c) a resistor (d) either a diode or a BJT- Special Diodes » Exercise - 1 1. A Zener diode : (a) Is a battery under forward biased condition (b) Acts like battery when it breakdowns (c) Is a switch (d) Is a device having barrier potential more than 5V 2. At 25ºC, a Zener diode rates at 2 watts, its power rating at 50ºC will be : (a) Zero watts (b) Less than 1 watt (c) Greater than 2 watts (d) Less than 2 watts 3. Silicon is appreciably employed as a base material compared to germanium while manufacturing Zener diode since : (a) silicon is abundantly available (b) it is costlier (c) it has low current capability (d) it has high temperature capability 4. The capacitance of a varactor diode increases, when the reverse voltage across it is : (a) Decreased (b) Increased (c) Kept constant (d) None of the above 5. The main advantage of a point contact diode is that : (a) The ratio of forward current to reverse current is very high (b) Low input impedance (c) Its cut-in voltage is equal to zero (d) Its reverse resistance is infinite 6. Which one of the following is a Square law device ? (a) Zener diode (b) Crystal diode (c) Tunnel diode (d) Varactor diode 7. Match the given lists. List I…
- Electronics Engineering » Notes » Operational Amplifier 1. The Op Amp is a widely used amplifier abstraction that forms the foundations of much of electronic circuit design. Op Amp devices are constructed using primitive elements such as transistors and resistors. 2. The Op Amp is a four-ported device. The ports include an input port with terminals usually labeled v+ and v− , an output port with one terminal labeled vo, and the other being ground, a positive power supply port with a +VS voltage applied with respect to ground, and a negative power supply port with a −VS voltage applied with respect to ground. Although the ground terminal is not explicitly shown in the Op Amp symbol, it is very much a part of all Op Amp circuits. 3. The Op Amp behaves like a voltage-dependent voltage source. Its input output relationship can can be expressed mathematically as vo=A(v+−v−) where A is a large number called the open loop gain of the amplifier. In most practical Op Amp applications, A is treated as infinity. 4. Most useful Op Amp circuits are built using the negative feedback connection, in which a portion of the output signal of the Op Amp is fed back to the v− input of the Op Amp. Examples of Op Amp circuits…
- 5555555555181. (a) 10011110 (b) 01211110 (c) 000100000100 (d) 001000001000
- 5555555555195. If B[7..0] = 10100101, what is the value of B[6..2]? (a) 10100 (b) 01001 (c) 10010 (d) 00101