BJT Amplifiers – Exercise – 2

71. In a hybrid equivalent circuit, ________ is determined to make it easier to find the other parameters.

(a) Zi
(b) Zo
(c) Ai
(d) Av

Answer
Answer : (d)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

72. The feedback pair uses a(n) ________ transistor driving a(n) ________ transistor, the two devices acting effectively much like one pnp transistor.

(a) pnp, npn
(b) pnp, pnp
(c) npn, npn
(d) None of the above

Answer
Answer : (a)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

73. In an unbypassed emitter-bias configuration ________ replaces re in the hybrid equivalent circuit.

(a) hie
(b) hfe
(c) hre
(d) hoe

Answer
Answer : (a)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

74. The output voltage and the input voltage are ________ for the common-base configuration.

(a) 45º out of phase
(b) 90º out of phase
(c) 180º out of phase
(d) in phase

Answer
Answer : (d)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

75. One junction of an operating transistor is ________ and the other one is ________.

(a) forward-biased, forward-biased
(b) forward-biased, reverse-biased
(c) reverse-biased, reverse-biased
(d) None of the above

Answer
Answer : (b)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

Related Posts

  • BJT Amplifiers - Exercise - 1BJT Amplifiers » Exercise - 1 1. Nota 2. The dc emitter current of a transistor is 8 mA. What is the value of re? (a) 320 (b) 13.3 k (c) 3.125 (d) 5.75 3. What is the most important r parameter for amplifier analysis? (a) rb (b) rc (c) (d) 4. Which of the h-parameters corresponds to re in a common-base configuration? (a) hib (b) hfb (c) hrb (d) hob 5. Under which of the following conditions is the output impedance of the network approximately equal to RC for a common-emitter fixed-bias configuration? (a) ro 10RC (b) ro 2 10RC (c) ro 2 ro (d) ro 4 ro 6. What is the unit of the parameter ho? (a) Volt (b) Ohm (c) Siemen (d) No unit 7. Which of the following gains is less than 1 for a common-base configuration? (a) Ai (b) Av (c) Ap (d) None of the above 8. Which of the following configurations has the lowest output impedance? (a) Fixed-bias (b) Voltage-divider (c) Emitter-follower (d) None of the above 9. Which one of the following configurations has the lowest input impedance? (a) Fixed-bias (b) Common-base (c) Emitter-follower (d) Voltage-divider? 10. The current gain for the Darlington…
    Tags: input, gain, high, voltage, low, output, impedance, common-emitter, phase, ac
  • BJT Amplifiers - 85555555555585. The common-emitter configuration has a ________ level of input impedance with a ________ voltage and current gain. (a) moderate, high (b) low, moderate (c) low, low (d) high, low
    Tags: low, high, common-emitter, configuration, level, input, impedance, voltage, current, gain
  • BJT Amplifiers - 63555555555563. What does the negative sign in the voltage gain of the common-emitter fixed-bias configuration indicate? (a) The output and input voltages are 180º out of phase. (b) Gain is smaller than 1. (c) Gain is larger than 1. (d) None of the above
    Tags: gain, output, larger, smaller, phase, input, configuration, fixed-bias, common-emitter, voltage
  • Single Stage Transistor Amplifiers - 1Single Stage Transistor Amplifiers » Exercise - 1 1. CE amplifier is characterised by : (a) low voltage gain (b) moderate power gain (c) signal phase reversal (d) very high output impedance
    Tags: gain, transistor, impedance, output, high, phase, voltage, low, electronics, engineering
  • BJT Amplifiers - 93555555555593. A common-base configuration has ________ impedance at the input and ________ impedance at the output. (a) high, high (b) high, low (c) low, low (d) low, high
    Tags: low, high, impedance, common-base, configuration, input, output, electronics, engineering

LEAVE A REPLY

Please enter your comment!
Please enter your name here