Active and Passive Filters – Exercise – 1

46. The maximum output voltage of a certain low-pass filter is 15 V. The output voltage at the critical frequency is ________.

(a) 0 V
(b) 15 V
(c) 10.60 V
(d) 21.21 V

Answer
Answer : (c)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

47. An RL low-pass filter consists of a 5.6 mH coil and a 3.3 kΩ resistor. The output voltage is taken across the resistor. The circuit’s critical frequency is ________.

(a) 93.8 kHz
(b) 93.8 Hz
(c) 861 Hz
(d) 86.12 kHz

Answer
Answer : (a)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

48. In a certain parallel resonant band-pass filter, the resonant frequency is 14 kHz. If the bandwidth is 4 kHz, the lower frequency ________.

(a) is 7 kHz
(b) is 10 kHz
(c) is 12 kHz
(d) cannot be determined

Answer
Answer : (c)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

49. A parallel resonant band-pass filter consists of a 90 Ω resistor in series with a parallel network made up of a 60 mH coil and a 0.02 μF capacitor. The output is taken across the capacitor/coil. The coil winding has a resistance of 20 Ω. What is the center frequency of the filter?

(a) 459 Hz
(b) 4,591 Hz
(c) 999 Hz
(d) 2,176 Hz

Answer
Answer : (b)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

50. The same signal in Problem 2 is applied to an RC high-pass filter. If the reactance is zero at the input frequency, the output voltage is

(a) 18 V peak-to-peak
(b) zero
(c) 9 V peak-to-peak
(d) 12.73 V peak-to-peak

Answer
Answer : (a)
Explanation
Explanation : No answer description available for this question. Let us discuss.
Discuss
Discuss : Write your answer. Click here.

Related Posts

  • Active and Passive Filters - 10Filters » Exercise - 110. A high pass filter is one which : (a) passes all high frequencies (b) attenuates all low frequencies (c) attenuates all frequencies below a designated cut-off frequency, and passes all frequencies above cut-off (d) none of these
    Tags: frequencies, passes, attenuates, cut-off, filter, frequency, electronics, engineering
  • Basic Op Amp Applications - 43555555555543. A low-pass filter ________. (a) provides a constant output up to the cutoff frequency (b) passes frequencies from zero up to the cutoff frequency (c) rejects all frequencies above the cutoff frequency (d) All of the above
    Tags: frequency, frequencies, low-pass, filter, output, passes, electronics, engineering
  • Active and Passive Filters - 9Filters » Exercise - 19. A low pass filter is one which : (a) passes all low frequencies (b) attenuates all high frequencies (c) passes all frequencies up to cut-off frequency, and attenuates all other frequencies (d) none of these
    Tags: frequencies, passes, attenuates, filter, cut-off, frequency, electronics, engineering
  • Active and Passive Filters - 525555555555 52. An RC low-pass filter consists of a 120 Ω resistor and a 0.002 μF capacitor. The output is taken across the capacitor. The circuit's critical frequency is ________. (a) 333 kHz (b) 633 kHz (c) 331 kHz (d) 60 kHz
    Tags: khz, capacitor, frequency, output, filter, low-pass, electronics, engineering
  • Active and Passive Filters - 15Filters » Exercise - 115. A band elimination filter is one : (a) which attenuates all frequencies less than lower cut-off frequency f1 (b) which attenuates all frequencies greater than upper cut-off frequency f2 (c) frequencies lying between f1 andf2 are attenuated and all other frequencies are passed (d) none of these
    Tags: frequencies, frequency, attenuates, cut-off, filter, band, electronics, engineering